To carry out a quality repair of the Philips blender, it is necessary to disassemble the cover and determine the malfunction by external signs. For example, you can see broken wires, “ring out” the contacts and clarify the location of the malfunction. Step-by-step instructions for disassembly and repair recommendations can be found in this article.
The content of the article
- What you need to work
- Step-by-step instruction
- Gearbox repair
- Nozzle repair
What you need to work
If you disassemble the Philips nl9206ad 4 blender or other models, you first need to prepare the tools:
- a set of curly and ordinary screwdrivers;
- magnet for removing small bolts;
- pliers;
- knife or metal plate for splitting latches and other parts;
- soldering iron;
- thermal gun;
- glue.
You need to disassemble the tool on a flat surface with good lighting in order to notice accidentally flying off bolts and other small parts in time. If in doubt, it is better to take a picture of the internal structure of the device, so that later it will be possible to correctly assemble it.
Step-by-step instruction
Disassembly of Philips nl9206ad 4 and other models goes in several stages. The sequence of actions is as follows:
- Pry off the top cover with a screwdriver or knife and remove it.
- Inside you can see 2 bolts that are unscrewed with a screwdriver.
- Next, remove the plastic part.
- Insert a screwdriver or knife as deep as possible and pry off the case.
- Continue to insert and loosen a little so that the inside freely comes out of the case.
- To repair a Philips blender, pry off the plastic nozzle and remove it.
- Unscrew the rotating part, as in the photo. If necessary, it can be removed completely and replaced with a new one.
- This is how the engine and other parts look like, if you get the entire base from the body.
- Now you need to carefully inspect the motor and control board - this will help determine the cause of the malfunction and perform the correct repair of the Philips submersible blender.
- Check buttons and replace if necessary.
- Check out the speed controller.
- Next, collect all the parts of the tool in reverse order and check how it works.
Gearbox repair
Now it’s clear how to disassemble the Philips 600 Watt blender. It remains to consider in more detail the different types of repair work that are carried out in the event of a breakdown of a particular part. To correctly establish the cause, you need to carefully examine the device assembled and disassembled, and also listen to how it works.
For example, if after disassembly it is noticeable that the wires have come off the board, you need to prepare a soldering iron and attach them to their original place. It also happens that breaks are not observed, but the brushes that supply current are worn out. They cannot be repaired - a complete replacement is required. It is not difficult to disassemble the brush, but it should be noted that its petals are rather weak, so it is undesirable to bend them.
If the bearings are worn out, it is necessary to apply a new stator winding. As a rule, such types of work are not carried out independently. Therefore, it is better to contact the service center.
Nozzle repair
Another common type of restoration work is the repair of the Philips blender head. Most often, the nozzle with knives breaks, which is used for making minced meat and mashed potatoes. If the knife is worn out, you can sharpen it yourself (if you have the skill) or simply contact the master.
But it also happens that the problem is related to the shaft. Then you need to disassemble the Philips blender - the instructions for this process are presented above. It is possible that the shaft is loosened due to constant exposure to vibration, which creates a gap, so the rotation does not work properly.
Repair in this case is quite complicated - it is easier to put a new shaft or even purchase another device. But in order to prevent breakage and not to disassemble the blender too often, it is recommended to periodically tighten the nut with which the knives are attached.
It is clear how to disassemble a Philips food processor or blender. To do this, you will need ordinary tools - screwdrivers, a knife and others. If you have the skill to diagnose a breakdown and fix it yourself. But if you are not sure, you should contact the master.
